iglidur® Z - material data

Table of contents

The most important specifications at a glance

Descriptive technical specifications
Wear resistance at +23°C- 🟧 🟧 🟧 🟧 ⬜️ +More information on wear resistance
Wear resistance at +90°C- 🟧 🟧 🟧 🟧 ⬜️ +
Wear resistance at +150°C- 🟧 🟧 🟧 🟧 ⬜️ +
Sliding properties- 🟧 🟧 🟧 🟧 🟧 +Coefficient of friction, dynamic, against steel: µ 0.06 - 0.14
Wear resistance under water- 🟧 🟧 ⬜️ ⬜️ ⬜️ +
Media resistance- 🟧 🟧 🟧 🟧 ⬜️ +More information on media resistance
Resistant to edge pressures- 🟧 🟧 🟧 🟧 🟧 +
Resistant to shock and impact loads- 🟧 🟧 🟧 🟧 🟧 +
Dirt resistance- 🟧 🟧 🟧 🟧 🟧 +

When do I use this material?

  • At temperatures up to +250°C, continuous, or +310°C, short-term
  • When low wear is required, especially under high radial load
  • At high surface speeds
  • For edge pressure in conjunction with higher surface pressures

When do I use a different material?

Temperatures

min. application temperatureUpper application temperature, long-termUpper application temperature, short-termIn addition secure axially from
-100°C+250°C+310°C+145°C

Permissible surface speed

Maximum surface speeds [m/s]RotatingOscillatinglinear
Long-term1.51.15.0
Short-term3.52.56.0

Permissible pv values

iglidur Z: logarithmic curve with a descending red line in a chart.
iglidur Z: logarithmic curve with a descending red line in a chart.

Mechanical specifications

Graph with a red line: the value decreases steadily from left to right.
Chart with two rising lines for +23 °C and +60 °C; the +60 °C line is higher.

Friction and wear

iglidur ZdryGreasesOilWater
Coefficient of friction μ0.06 - 0.140.090.040.04
Chart with a red curve: the value rises to about 0.20, then falls slightly.
Chart with a descending red curve in a coordinate system.

Shaft materials

Bar chart with categories A to G; E is the highest, and B is the second highest.
Chart with two curves A and B on X and Y axes, where A rises more steeply than B.

Chemical resistance

ChemicalsResistance
Alcohols0
Greases, oils without additives+
Hydrocarbons+
Fuels+
Strong alkalines-
Strong acids-
Diluted alkalines+
Diluted acids+

Moisture absorption

Chart with a rising curved line on the X and Y axes.

Installation tolerances

Diameter d1 [mm]Housing H7 [mm]iglidur Z plain bearing F10 [mm]Shaft h9 [mm]
up to 3+0.000 +0.010+0.006 +0.046-0.025 +0.000
> 3 up to 6+0.000 +0.012+0.010 +0.058-0.030 +0.000
> 6 up to 10+0.000 +0.015+0.013 +0.071-0.036 +0.000
> 10 up to 18+0.000 +0.018+0.016 +0.086-0.043 +0.000
> 18 up to 30+0.000 +0.021+0.020 +0.104-0.052 +0.000
> 30 up to 50+0.000 +0.025+0.025 +0.125-0.062 +0.000
>50 to 80+0.000 +0.030+0.030 +0.150-0.074 +0.000
>80 to 120+0.000 +0.035+0.036 +0.176-0.087 +0.000
> 120 up to 180+0.000 +0.040+0.043 +0.203+0.000 +0.100

Thermal conductivity

Coefficient of thermal expansion

Compressive strength

Vacuum

Radioactive radiation

Typical areas of application

Dump truck with marked bearing points and iglidur Q2E for heavy machinery.

Construction machinery industry

Textile threads run through an industrial weaving machine.

Textile industry

Passenger airplane on final approach over a runway.

Aerospace technology

Consulting

I look forward to answering your questions

RAILONVIRTA_Mikko_igus_FI
Mikko Railonvirta

Sales Manager

+358 (0)40 3412 396 Write e-mail

Shipping and consultation